What're your thoughts and feelings on Tools You Need to Install a New Bathtub ?
Installing a bathtub isn't specifically brain surgery, but it does call for strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old tub with a new one is likewise a moderately challenging project. If the old bathtub is conveniently available, the project can move speedily; if you need to open up a wall surface to get rid of the old tub and position the brand-new bathtub, the job is a lot harder. In either situation, the task is within a house handyman's abilities, although you will need an assistant to vacate the old bathtub and set in the brand-new one. See to it you have qualified yourself for the job as well as fit trying it. As opposed to working with a professional to take over a halfway-completed job, it is much better to think about utilizing one before you begin. Chances are you may require a specialist plumber to make tube links.
This post will help you install a brand-new tub in your shower room if you have currently gotten a new tub as well as don't require to alter the setup of your previous water system pipes.
Your devices as well as product checklist need to comprise the following:
Getting ready for the Installation
First of all, the sustaining framework provided with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its last setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the supply of water. After doing so, activate the faucets to drain any type of water remaining in the system. The process of removing the existing faucets can be fairly troublesome as a result of the limited gain access to that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a towel prepared for the staying water that will come from the pipelines. When the supply pipelines have been removed, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned up of any old sealing substance.
Prior to moving on to fit the new taps, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using the two wood boards under its feet, place the bath tub in the called for placement. The wood boards are practical in equally spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto four tiny factors.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out level.
To set up taps, fit all-time low of the outermost adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the various other faucet.
Switch on the water and examine all joints and new pipework for leakages and also tighten them if necessary. Fill up the bath tub as well as also check the overflow outlet as well as the regular electrical outlet for leakages.
Finally, fix the bath paneling as explained in the producer's instruction manual. Tiling as well as securing around the tub must wait up until the tub has been used at the very least when as this will certainly resolve it into its final position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making certain that the washers remain in area between the tap and also the sink. Secure the tap in position with the manufacturer offered backnut. As soon as the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type should be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack a stiff seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, causing difficulties with dampness and possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes and also cartridges, and are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily available on the market. It is advisable to fit the floor tiles making use of waterproof or waterproof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our piece about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Many thanks for finding the time to browse our article post. If you please take the opportunity to distribute this blog post if you enjoyed reading it. I appreciate reading our article about Installing A Bathtub.
Burst pipe? Phone!